You are using a wrong disk image my friends.
For beaglebone black, you should have used miniroot-am335x-54.fs
The one you are using is for beagleboard.
Read the doc: INSTALL.armv7
-Edward
------------------------------------------------------------------------
From: "Joseph S. Testa II" <jte...@positronsecurity.com>
To: "arm@openbsd.org" <arm@openbsd.org>
Sent: December 4, 2013 2:27 PM
Subject: Problem Installing on Beagle Bone Black
Hi all,
I'm trying to install the snapshot from
http://ftp.openbsd.org/pub/OpenBSD/snapshots/armv7/miniroot-beagle-54.fs
to my new Beagle Bone Black. Unfortunately, I get a lot of
"Input/output error" messages when I try to install it to the internal
flash memory.
Below is the full serial output that shows what I'm running into.
Any ideas?
Thanks in advance,
- Joe
U-Boot SPL 2013.04-rc1-14237-g90639fe-dirty (Apr 13 2013 - 13:57:11)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-rc1-14237-g90639fe-dirty (Apr 13 2013 - 13:57:11)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
151 bytes read in 4 ms (36.1 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
reading bsd.umg
4518555 bytes read in 584 ms (7.4 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4518491 Bytes = 4.3 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
OpenBSD/beagle booting ...
arg0 0x0 arg1 0xe05 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x20000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 131072/0x20000000
Allocating page tables
freestart = 0x80729000, free_pages = 129239 (0x0001f8d7)
IRQ stack: p0x80757000 v0xc0757000
ABT stack: p0x80758000 v0xc0758000
UND stack: p0x80759000 v0xc0759000
SVC stack: p0x8075a000 v0xc075a000
Creating L1 page table at 0x8072c000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ no symbol table formats found ]
board type: beaglebone
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2013 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.4-current (RAMDISK-OMAP) #0: Wed Oct 30 16:50:18 CET 2013
r...@imx.office.jasper.la:/usr/src/sys/arch/armv7/compile/RAMDISK-OMAP
real mem = 536870912 (512MB)
avail mem = 518184960 (494MB)
mainbus0 at root
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0: BeagleBone
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
intc0 at omap0 rev 5.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
omdog0 at omap0 rev 0.1
ommmc0 at omap0
sdmmc0 at ommmc0
ommmc1 at omap0
sdmmc1 at ommmc1
com0 at omap0: ti16750, 64 byte fifo
com0: console
cpsw0 at omap0: version 1.12 (0), address c8:a0:30:b0:b8:3c
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI
0x0001ff
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: SCSI2 0/direct fixed
sd0: 7580MB, 512 bytes/sector, 15523840 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: SCSI2 0/direct fixed
sd1: 1832MB, 1024 bytes/sector, 1875968 sectors
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 5.4 installation program.
(A)utoinstall, (I)nstall, (U)pgrade or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN. You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.
Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') bbb
Available network interfaces are: cpsw0.
Which one do you wish to configure? (or 'done') [cpsw0]
IPv4 address for cpsw0? (or 'dhcp' or 'none') [dhcp]
Issuing hostname-associated DHCP request for cpsw0.
DHCPDISCOVER on cpsw0 to 255.255.255.255 port 67 interval 1
DHCPOFFER from 192.168.1.1 (30:46:xx:xx:xx:xx)
DHCPREQUEST on cpsw0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1 (30:46:xx:xx:xx:xx)
bound to 192.168.1.104 -- renewal in 43200 seconds.
IPv6 address for cpsw0? (or 'rtsol' or 'none') [none]
Available network interfaces are: cpsw0.
Which one do you wish to configure? (or 'done') [done]
Using DNS domainname my.domain
Using DNS nameservers at 192.168.1.1
Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes]
Start ntpd(8) by default? [no]
Setup a user? (enter a lower-case loginname, or 'no') [no]
What timezone are you in? ('?' for list) [US/Eastern]
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0] sd1
Use DUIDs rather than device names in fstab? [yes]
fdisk: sd1: Input/output error
MBR has invalid signature; not showing it.
Use (W)hole disk or (E)dit the MBR? [whole] w
Creating a msdos partition and an OpenBSD partition for rest of
sd1...fdisk: sdr
done.
disklabel: /dev/rsd1c: Input/output error
newfs_msdos: /dev/rsd1i: Input/output error
The auto-allocated layout for sd1 is:
disklabel: /dev/rsd1c: Input/output error
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] a
disklabel: /dev/rsd1c: Input/output error
fdisk: sd1: Input/output error
MBR has invalid signature; not showing it.
Use (W)hole disk or (E)dit the MBR? [whole]
