You don't state what kernel version you're running is.
On Mon, Nov 1, 2021 at 4:44 PM Peter Boy <[email protected]> wrote: > > I tried to install F35 on my Rock Pi 4 A yesterday and ended up with a > basically working box but without an ethernet connection. An ‚ip a‘ just > shows the device without any IP settings. After setting hostname and locale > and reboot I got an IPv6 local link (fe80::…) but nothing else. And after a > while that vanished, too. > > A 'nmcli dev‘ shows an ethernet device eth0, at first in status ‚connection‘ > and after a while ‚disconnected‘. > A ’nmcli con’ first showed ‚wired connection 1‘ and device eth0, later no > device. > > > In boot log I found several entries with warnings about something not found, > but in the end: > > rk_gmac-dwmac fe300000.ethernet: Ring mode enabled > rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer > RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver > (mii_bus:phy_addr=stmmac-0:01, irq=POLL) > > And NetworkManager > > (NM)[1103]: <info> ... device (lo): carrier: link connected > (NM)[1103]: <info> ... manager: (lo): new Generic device > (/org/freedesk...ces/1) > (NM)[1103]: <info> ... device (eth0): driver '(null)' does not support > carrier detection. > (NM)[1103]: <info> ... device (eth0): driver 'rk_gmac-dwmac' does not > support carrier detection. > (NM)[1103]: <info> ... manager: (eth0): new Ethernet device > (/org/freede.../Devices/2) > (NM)[1103]: <info> ... settings: (eth0): created default wired connection > 'Wired connection 1' > (NM)[1103]: <info> ... device (eth0): state change: unmanaged -> unavailable > (reason 'managed', sys-iface-state: 'external‘) > > rk_gmac-dwmac fe300000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E > Gigabit Ethernet] (irq=POLL) > rk_gmac-dwmac fe300000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 > rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found > rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW > rk_gmac-dwmac fe300000.ethernet eth0: configuring for phy/rgmii link mode > ... > rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control > rx/tx > > > With current fully updated F34 everything works fine, even PCIe NVMe ssd M.2 > works. > > I hesitate to update to F35 online. If I then find myself without a network > connection, it is difficult to reinstall F34 (with the F34 install image the > network works, but not the terminal). > > > > Any idea how getting this to work? > > > > Any help greatly appreciated. > > Peter > > > > > > > _______________________________________________ > arm mailing list -- [email protected] > To unsubscribe send an email to [email protected] > Fedora Code of Conduct: > https://docs.fedoraproject.org/en-US/project/code-of-conduct/ > List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines > List Archives: > https://lists.fedoraproject.org/archives/list/[email protected] > Do not reply to spam on the list, report it: > https://pagure.io/fedora-infrastructure _______________________________________________ arm mailing list -- [email protected] To unsubscribe send an email to [email protected] Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/[email protected] Do not reply to spam on the list, report it: https://pagure.io/fedora-infrastructure
