It looks like the wrong partition. Try extload 1:1 or something. I think mine ended up on diak 1 or 2... You may have to make some other changes as well.
----- Reply message ----- From: "Robert Moskowitz" <[email protected]> To: "Derek Atkins" <[email protected]> Cc: "[email protected]" <[email protected]>, "Paul Whalen" <[email protected]>, <[email protected]> Subject: [fedora-arm] Bad image/instructions? - Re: Problems with a pogoplug v02 Date: Tue, Apr 23, 2013 12:22 pm On 04/23/2013 09:03 AM, Derek Atkins wrote: > "[email protected]" <[email protected]> writes: > >> Ext2ls and the usb start commands are built into uboot. You need to be at the >> uboot prompt to use them. > Just FTR, the default version of uboot shipped on the Guruplug Server > (at least on the two non-Plus version I have) did not include ext > support. I had to reflash uboot to a newer version. I posted this in an earlier part of this thread. Here is what I see in the nc session for the netconsole. You tell me if it is supporting ext. I did make the documented changes to uboot for f18 (which I don't have that link in front of me, but Scott's. U-Boot 2011.12 (Feb 20 2012 - 21:21:59) Pogoplug E02 arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000008000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 728 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 717 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "uImage" from usb device 0:1 (usbda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported Loading file "uImage" from usb device 0:1 (usbda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** Loading file "uInitrd" from usb device 0:1 (usbda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ........ done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
_______________________________________________ arm mailing list [email protected] https://admin.fedoraproject.org/mailman/listinfo/arm
