Hi chaitanya, can you tell me how to run pppd from init.rc file.
one more thing here is if i run rild daemon,then pppd getting failed. On Tue, Jan 17, 2012 at 2:35 PM, venkat k raju <[email protected]> wrote: > sorry without rild interface i am connecting internet > > > On Tue, Jan 17, 2012 at 2:35 PM, venkat k raju <[email protected]>wrote: > >> Hi Devindrappa Handraki, >> >> i had been trying it........... for me both are not working at time... >> here i am using mux concept also.. !!!!!!!! >> >> i don't know what happen in your case....but with rild interface i have >> been connection the net .. >> see once again... >> 1) i written code for manually enter at commands!!!!! >> in this #AT+CGREG=1 >> #AT^SGAUTH=0 // in your case no need of this command. >> #At+cgatt=1 >> # AT+Cgdcont=1,IP,BSNLNET >> 2) >> >> /system/bin/pppd nodetach debug /dev/ttyACM0 115200 nocrtscts local >> 0.0.0.0:10.0.0.1 noipdefault ipcp-accept-local connect '/system/bin/chat >> -v -s -f /system/etc/ppp/gprs_chat' defaultroute usepeerdns modem updetach >> noauth >> >> 3) gprs_chat.sh file contains >> >> ABORT 'BUSY' >> ABORT 'NO CARRIER' >> ABORT 'VOICE' >> ABORT 'NO DIALTONE' >> ABORT 'NO DIAL TONE' >> ABORT 'NO ANSWER' >> ABORT 'DELAYED' >> REPORT CONNECT >> TIMEOUT 6 >> '' >> 'AT+CGDCONT=1,"IP","airtelgprs.com"' >> 'OK' 'ATD*99***1#' >> TIMEOUT 30 >> CONNECT '' >> >> >> >> >> >> On Tue, Jan 17, 2012 at 2:23 PM, Devindrappa Handraki < >> [email protected]> wrote: >> >>> Hi venkat and Chaitanya, >>> >>> 1. I am not able to access Internet, i am getting the below mentioned >>> error >>> E/pppd ( 1799): Connect script failed >>> I/pppd ( 1802): ######### pppd exited with 8 >>> >>> 2. Do we need to configure mux driver for internet access and telephone >>> services. If so please give me some hints. >>> >>> Thanks and Regards, >>> Devindrappa >>> >>> >>> >>> >>> On Tue, Jan 17, 2012 at 9:12 AM, venkat k raju <[email protected]>wrote: >>> >>>> >>>> Hi Chaitanya & Devindrappa, >>>> >>>> thanks for your suggestions. >>>> >>>> finally i am able to establish GPRS and GSM individually. >>>> if i tried both at time then my usb (modem) was disconnecting. >>>> >>>> i have been trying it... !!!!!!!!! >>>> >>>> >>>> On Mon, Jan 16, 2012 at 5:23 PM, Sai Chaitanya Chitneedi < >>>> [email protected]> wrote: >>>> >>>>> Hi venkat, >>>>> I'm not aware of the mux driver and config binary you are using. >>>>> Assuming it works well, it seems like a permission problem or a locked >>>>> socket problem. do a "lsof" on /dev/socket/rild (socket used by android to >>>>> communicate with ril daemon) for any exsting locks and check its >>>>> permissions. Try with the physical port first,after killing the rild. Then >>>>> try with your virtual port. >>>>> >>>>> Also if it suits your purpose use a soft link instead of virtual ports. >>>>> >>>>> On Mon, Jan 16, 2012 at 11:25 AM, venkat k raju >>>>> <[email protected]>wrote: >>>>> >>>>>> >>>>>> Hi chaitanya, >>>>>> can you explain me how to establish gsm on gingerbread. >>>>>> >>>>>> i am following there steps to manually establish GSM/GPRS .... please >>>>>> correct me. >>>>>> >>>>>> >>>>>> #chmod 0666 /dev/ttyACM0 /********* my physical serial port*******/ >>>>>> # chown radio.radio /dev/ttyACM0 >>>>>> # insmod ./linmux.ko /*************** my mux driver to create >>>>>> virtual port *********/ >>>>>> # chmod 0666 /dev/ttyMux1 >>>>>> # chmod 0666 /dev/ttyMux2 >>>>>> # chmod 0666 /dev/ttyMux0 >>>>>> # chown radio.radio /dev/ttyMux0 >>>>>> # chown radio.radio /dev/ttyMux1 >>>>>> # chown radio.radio /dev/ttyMux2 >>>>>> >>>>>> #mknod /dev/muxcfg c 239 0 /****** i am creating the interface >>>>>> driver***********/ >>>>>> >>>>>> #/system/bin/linmuxcfg -p=/dev/ttyACM0 /******** configuring the >>>>>> physical port to virtual port **********/ >>>>>> >>>>>> then i am trying to kill rild daemon then i am trying execute the >>>>>> bellow command for GSM as well as gprs with new virtual serial port. >>>>>> >>>>>> #/system/bin/rild -l /system/lib/libreference-ril.so -- -d >>>>>> /dev/ttyMux0 >>>>>> >>>>>> but here i got the error like this >>>>>> >>>>>> >>>>>> I/RIL ( 360): Opening tty device /dev/ttyMux0 >>>>>> E/RILC ( 360): Failed to get socket 'rild' >>>>>> >>>>>> >>>>>> please suggest me !!!!!!! >>>>>> >>>>>> thanks&Regards >>>>>> k.v.raju >>>>>> >>>>> >>>>> >>>> >>>> >>>> -- >>>> thanks&Regards >>>> k.v.raju >>>> >>> >>> >> >> >> -- >> thanks&Regards >> k.v.raju >> > > > > -- > thanks&Regards > k.v.raju > -- thanks&Regards k.v.raju -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
