Hi, I am getting the following error when i try to port the Kernel image i obtained through the following link,
git://labs.embinux.org/repo/android/platform/omap3manifest.git. > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2075720 Bytes = 2 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing > Linux............................................................. > ......................................................................... > done, > booting the kernel. > Linux version 2.6.29-omap1-07255-g85f0546 ([email protected]) ( For > any > Queries, information and bug reports please mail to [email protected] ) #1 > Thu Se > p 10 18:54:14 IST 2009 > CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > Machine: OMAP3 Beagle Board > Memory policy: ECC disabled, Data cache writeback > OMAP3430 ES2.1 > SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 > Reserving 12582912 bytes SDRAM for VRAM > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 > video=o > mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1 > nohz=o > ff androidboot.console=ttyS2 > Unknown boot option `androidboot.console=ttyS2': ignoring > Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz > GPMC revision 5.0 > IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts > Total of 96 interrupts on 1 active controller > OMAP34xx GPIO hardware version 2.5 > PID hash table entries: 512 (order: 9, 2048 by > OMAP clockevent source: GPTIMER12 at 32768 Hz > Console: colour dummy device 80x30 > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) > Memory: 128MB = 128MB total > Memory: 112768KB available (3824K code, 718K data, 144K init) > Calibrating delay loop... 484.21 BogoMIPS (lpj=1892352) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > net_namespace: 520 bytes > regulator: core version 0.5 > NET: Registered protocol family 16 > Found NAND on CS0 > Registering NAND on CS0 > OMAP DMA hardware revision 4.0 > bio: create slab <bio-0> at 0 > OMAP DSS rev 2.0 > OMAP DISPC rev 3.0 > OMAP VENC rev 2 > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz > twl4030: PIH (irq 7) chaining IRQs 368..375 > twl4030: power (irq 373) chaining IRQs 376..383 > twl4030: gpio (irq 368) chaining IRQs 384..401 > regulator: VMMC1: 1850 <--> 3150 mV normal standby > regulator: VDAC: 1800 mV normal standby > regulator: VUSB1V5: 1500 <--> 0 mV normal standby > regulator: VUSB1V8: 1800 <--> 0 mV no > regulator: VUSB3V1: 3100 <--> 0 mV normal standby > regulator: VPLL2: 1800 mV normal standby > regulator: VSIM: 1800 <--> 3000 mV normal standby > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz > SCSI subsystem initialized > twl4030_usb twl4030_usb: Initialized TWL4030 USB module > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 > musb_hdrc: USB OTG mode controller at d80ab000 u > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 4096 (order: 3, 32768 bytes) > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) > TCP: Hash tables configured (established 4096 bind 4096) > TCP reno registered > NET: Registered protocol family 1 > NetWinder Floating Point Emulator V0.97 (double precision) > ashmem: initialized > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. > msgmni has been set to 220 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler anticipatory registered (default) > io scheduler deadline registered > io scheduler cfq registered > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 > serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > console [ttyS2] enabled > brd: module loaded > loop: module loaded > i2c /dev entries driver > Driver 'sd' needs updating - please use bus_type methods > omap2-nand driver initializing > NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V > 16-bi > t) > cmdlinepart partition parsing not available > Creating 5 MTD partitions on "omap2-nand": > 0x000000000000-0x000000080000 : "X-Loader" > 0x000000080000-0x000000260000 : "U-Boot" > 0x000000260000-0x000000280000 : "U-Boot Env" > 0x000000280000-0x000000680000 : "Kernel" > 0x000000680000-0x0000100000 > usbmon: debugfs is not available > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: OMAP-EHCI Host Controller > usb usb1: Manufacturer: Linux 2.6. > usb usb1: SerialNumber: ehci-omap.0 > Start > usb usb1: configuration #1 chosen from 1 choiceU-Boot 1.3.3 (Jul 10 2008 - > 16:33:09) > hub 1-0:1.0: USB hub found > > OMAP3530-GP rev 2, CPU-O > hub 1-0:1.0: 3 ports detected > OMAP3 Be > Initializing USB Mass Storage driver... > DRAM: 128 MB > usbcore: registered new interface driver usb-storage > Out: serial > Err: serial > USB Mass Storage support registered.omplete > android initny key to st > android_bind 0 > mass_storage_function_addP3 beagleboard.org # sete > android_usb gadget: Number of LUNs=1e: > setenv - set environment v > adb_function_add > android_usb gadget: android_usb readyootargs > musb_hdrc musb_hdrc: MUSB HDRC host driver > OMAP3 > musb_hdrc musb_hdrc: new USB bus registered, assigned bus numtry 'help' > > usbcore: registered new interface driver usbhid > usbhid: v2.6:USB HID core driverin variable name "bootargs=conso > logger: created 64K log 'log_main' > logger: created 256K log 'log_events' beagleboard.org # setenv bootargs > logger: created 64K log 'log_radio' > Unknown command 'setenv' - try 'he > Advanced Linux Sound Architecture Driver Version 1.0.18a..org # setenv > bootargs=console=ttyS2,115200n8 noinitrd ro > No device for DAI AD73311 > No device for DAI AK4535 > v/mmcblk0p2 v > No device for DAI cs4270x720mr...@50 init=/init > No device for DAI PCM3008 HiFi > No device for DAI SSM2602 > rootdelay=1 > No device for DAI tlv320aic23tyS2 > No device for DAI tlv320aic3xr: illegal character '=' in v > No device for DAI twl4030sole=ttyS2,115200n > No device for DAI UDA134X > No device for DAI UDA1380 > > No device for DAI WM8580 PAIFTX > No device for DAI WM8728 > rootdelay=1 > No device for DAI WM8731ole=ttyS2 > No device for DAI WM8750 > OMAP3 beagleboar > No device for DAI WM8753 DAI 0 > Saving Environ > No device for DAI WM8753 DAI 1 > Erasing Nand...W > No device for DAI WM8971 > No device for DAI WM8990 ADC/DAC Primaryenv > file > No device for DAI omap-mcbsp-dai-0mmcinit;fatload mmc 0 0x80300000 u > No device for DAI omap-mcbsp-dai-1 > No device for DAI omap-mcbsp-dai-2 > stdout=serial > No device for DAI omap-mcbsp-dai-3s=console=ttyS2,115200n8 noinitrd > No device for DAI omap-mcbsp-da > OMAP3 be > TCP cubic registered > > T > NET: Registered protocol family 17 > Startin > NET: Registered protocol family 15 > > > U-Boot 1.3.3 (Jul 10 20 > RPC: Registered udp transport module. > > OMAP3530-GP rev 2, CPU > RPC: Registered tcp transport module. > OMAP3 Beagle Board + L > Power Management for TI OMAP3. > DRAM: 128 MB > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1rial > Err: serial > Audio Tone on Speakers .. > Console: switching to colour frame buffer device 80x30key to stop autoboot: 0 > clock: clksel_round_rate_div: dpll4_m4_ck target_rate 3 > > Freeing init memory: 144K1 Thu Se > Warning: unable to open an initial console. > p 10 18:54:14 IST 2009 > Failed to execute /init. Attempting defaults...082] revision 2 (ARMv7), > cr=10c5387f > Kernel panic - not syncing: No init found. Try passing init= option to > kernel.ache, VIPT nonaliasing instruction cache > android_usb gadget: high speed config #1: androide Board > Memory policy: > android_usb gadget: high speed config #1: android > OMAP3430 ES2.1 > android_usb gadget: high speed config #1: androidd7000000 size: 0x100000 > > > Texas Instruments X-Loader 1.41eserving 12582912 bytes SDRAM f > Starting OS Bootloader... > > > > DRAM: 128 MB=o > NAND: 256 MiB > In: serial > Out: serialmapfb.mode=dv > Err: seri...@50 init=/in > Audio Tone on Speakers ... completez=o > Hit any key to stop autoboot: 0 > ff androidboot.co > reading uImage > > 2075784 bytes readoot option `androi > ## Booting kernel from Legacy Image at 80300000 ... > Clocking rate ( > Image Name: Linux-2.6.29-omap1-07255-g85f054 > GPM > Image Type: ARM Linux Kernel Image (uncompressed)xd8200000 (revision > 4.0) with 96 interrupts > Data Size: 2075720 Bytes = 2 MB > Total of 96 interrupt > Load Address: 80008000 > Entry Point: > > Uncompressing > Linux............................................................. > Console: colour dummy device 80x30 > ......................................................................... > done, > Inode-cache hash table entri > booting the kernel.32768 bytes) > Linux version 2.6.29-omap1-07255-g85f0546 ([email protected]) ( For > any > Memory: 112768KB available (3824K code, 718K data, 1 > Queries, information and bug reports please mail to [email protected] ) #1 > Thu Seg delay loop... 483.16 BogoMIPS (lpj=1888256) > p 10 18:54:14 IST 2009unt-cache hash table e > CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387fe buffer > coherency: ok > > Memory policy: ECC disabled, Data cache writeback > OMAP DMA hardware revision 4.0 > OMAP3430 ES2.1 > bio > SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000P DSS rev 2.0 > OMAP DISPC rev 3.0 > Reserving 12582912 bytes SDRAM for VRAMi2c_omap i2c_omap.1: bus 1 rev3.12 at 2 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: > 32512chaining IRQs 368..375 > twl4030: > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 > video=o > twl4030: gpio (irq 368) chaining IRQs 384..401 > mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1 > nohz=o > regulator: VDAC: 1800 mV normal standby > ff androidboot.cons > i2c_oma > OMAP34xx GPIO hardware version 2.5kHz > PID hash table entries: 512 (order: 9, 2048 bytes) > twl4030_usb twl4030_usb: Initiali > OMAP clockevent source: GPTIMER12 at 32768 Hz > usbcore: regi > Console: colour dummy device 80x30 > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) > usbcore: registered new d > Inode-cache hash table entries: 8192 (orde > > net_namespace: 520 bytesed hash table entries: 4 > regulator: core version 0.5 > NET: Registered protocol family 16 > TCP bind hash table entries: 409 > Found NAND on CS0 bytes) > Registering NAND on CS0 > OMAP DMA hardware revision 4.0stablished 4096 bind 4096) > bio: create slab <bio-0> at 0 > TCP re > OMAP DSS rev 2.0 > > OMAP DISPC rev 3.0tocol family 1 > OMAP VENC rev 2 > N > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHzprecisio > regulator: VUSB1V5: 1500 <--> 0 mV normal standbyticipatory registered > (default) > regulator: VUSB1V8: 1800 <--> 0 mV normal standby registered > io sc > regulator: VUSB3V1: 3100 <--> 0 mV normal standbySerial: 8250/16550 driver, 4 > ports, IRQ sharing e > regulator: VPLL2: 1800 mV normal standby > serial8250.0: ttyS0 > regulator: VSIM: 1800 <--> 3000 mV normal standby > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz(irq > i2c /dev > usbcore: registered new interface driver hub 'sd' needs updating - please use > bus_type m > usbcore: registered new device driver usb > omap2-nand driver in > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0r ID: 0x2c, > Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bi > musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92 > t) > cmdlinepart partition parsing not available > NET: Registered protocol family 2 > Creating 5 MTD partitions on "o > IP route cache hash table entries: 1024 (order: 0, 4096 > bytes)00000-0x000000080000 : "X-Loader" > TCP established hash table entries: 4096 (order: 3, 32768 bytes) > 0x000000260000-0x000000280 > ashmem: initialized.0: new USB bus reg > VFS: Disk quotas dquot_6.5.21 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)ap.0: irq 77, io > mem 0x48064800 > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.started, EHCI 1.00 > msgmni has been set to 220ew USB device found, idVen > alg: No test for stdrng (krng) > io scheduler noop registeredusb1: New USB device strings > io scheduler anticipatory registered (defa > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > usb usb1 > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654usb usb1: > configuration #1 chosen from 1 choice > serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > hub 1-0:1.0: 3 ports detected > serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > usbcore: registered new in > console [ttyS2] enabledge > brd: module loaded > USB M > loop: module loadedregistered. > i2c /dev entries driver > android init > Driver 'sd' needs updating - please use bus_type methods > android_usb gadget: Number of > omap2-nand driver initializing > adb_function_add > 0x000000080000-0x000000260000 : "U-Boot" > usb usb2: Product: MUSB HDRC > 0x000000260000-0x000000280000 : "U-Boot Env" > usb usb2: Manufacturer: Linux 2.6.29- > 0x000000280000-0x000000680000 : "Kernel" > 0x000000680000-0x000010000000 : "File System"rc > usb usb2: > usbmon: debugfs is not availablehoice > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > hub 2-0:1.0: 1 port detected > ehci-omap ehci-omap.0: OMAP-EHCI Host C > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > logger: created 64K log 'log_radio' > usb usb1: Product: OMAP-EHCI Host Controllerux Sound Architecture Driver > Version 1.0.18a > usb usb1: Manufacturer: Linux 2.6.29-omap1-07255-g85f0546 ehci_hcde for DAI > AD73311 > No device for DAI AK453 > usb usb1: SerialNumber: ehci-omap.0for DAI CS4270 > usb usb1: configuration #1 chosen from 1 choice > No device for DAI SSM2602 > hub 1-0:1.0: USB hub fou > USB Mass Storage support registered.e for DAI UDA1380 > android initice for DAI > android_bind > mass_storage_function_addWM8510 HiFi > android_usb gadget: Number of LUNs=1580 PAIFRX > adb_function_addor DAI WM8580 PA > android_usb gadget: android_usb ready device for DAI WM8728 > musb_hdrc musb_hdrc: MUSB HDRC host driver > No device for DAI WM8750 > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 > No device for DAI WM8753 DAI 1 > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002o device for DAI > WM8990 ADC/DAC Primary > usb usb2: New USB device strings: Mfr=3, Prbsp-dai-0 > usb usb2: SerialNumber: musb_hdrc > OMAP > usb usb2: configuration #1 chosen from 1 choiceudio Codec init > asoc: t > hub 2-0:1.0: USB hub found mapping ok > hub 2-0:1.0: 1 port detected > ALSA device list: > twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0P cubic > registered > NET: Registered protocol f > twl4030_rtc twl4030_rtc: Power up reset detected.gistered protocol family 15 > twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.le. > RPC: > mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock > Power Management for TI OMAP3. > usbcore: registered new interface driver usbhid architectu > No device for DAI CS42702000-01-01 00:06:40 UTC > No device for DAI PCM3008 HiFi > No device for DAI SSM2602 > 200) > Waiting 1sec be > No device for DAI tlv320aic23 > No device for DAI tlv320aic3xeed SD card at address b368 > No device for DAI twl4030 > mmcblk0: > No device for DAI UDA134X > No device for DAI UDA1380 > android_usb > No device for DAI UDA1380#1: android > No device for DAI UDA13 > > EXT3-fs: > No device for DAI WM8731ordered data mode. > No device for DAI WM8750 > VFS > No device for DAI WM8753 DAI 0) on device 179:2. > No device for DAI WM8753 DAI 1 > Freeing init memory: > No device for DAI WM8971 > Warning: unable to > No device for DAI WM8990 ADC/DAC Primary > Failed to ex > No device for DAI omap-mcbsp-dai-0. > No device for DAI omap-mcbsp-dai-1syncing: No init found. Try passi > No device for DAI omap-mcbsp-dai-2 > No device for DAI omap-mcbsp-dai-3 > android_usb gadget: high speed c > No device for DAI omap-mcbsp-dai-4 > an > OMAP3 Beagle SoC init speed config #1: and > TWL4030 Audio Codec init > TWL4030 Audio Codec init > Console: switching to colour frame buffer device 80x30 > clock: clksel_round_rate_div: dpll4_m4_ck target_rate 36000000 > clock: new_div = 12, new_rate = 36000000 > omapdss: Could not find exact pixel clock. Requested 23500 kHz, got 24000 kHz > twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC > (946684 > 800) > Waiting 1sec before mounting root device... > mmc0: new high speed SD card at address b368 > mmcblk0: mmc0:b368 SD 1.88 GiB > mmcblk0: p1 p2 > android_usb gadget: high speed config #1: android > kjournald starting. Commit interval 5 seconds > EXT3 FS on mmcblk0p2, internal journal > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with ordered data mode. > VFS: Mounted root (ext3 filesystem) on device 179:2. > Freeing init memory: 144K > Warning: unable to open an initial console. > Failed to execute /init. Attempting defaults... > Kernel panic - not syncing: No init found. Try passing init= option to > kernel. > android_usb gadget: high speed config #1: android > android_usb gadget: high speed config #1: android > android_usb gadget: high speed config #1: android Please help! --~--~---------~--~----~------------~-------~--~----~ unsubscribe: [email protected] website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---
