Hi Alex,
Thanks for the suggestion!
What I am thinking is "DRM_DEV_INFO" should not be the one we want - as
it is more like a debug message.
[drm:jpeg_v5_0_0_hw_init [amdgpu]] JPEG decode initialized successfully.
instead I prefer to use this format:
"amdgpu 0000:43:00.0: amdgpu: JPEG decode initialized successfully."
but again I dislike it as well as there are 2 "amdgpu"s in the same message.
To make it consistent the "DRM_INFO" is used everywhere in the amdgpu code.
only the following jpeg code uses DRM_DEV_INFO and one file for vcn. All
other jpeg versions have already changed to DRM_INFO.
grep -r DRM_DEV_INFO *
amdgpu/jpeg_v4_0_3.c: DRM_DEV_INFO(adev->dev, "JPEG decode
initialized successfully.\n");
amdgpu/jpeg_v4_0_3.c: DRM_DEV_INFO(adev->dev, "JPEG decode is
enabled in VM mode\n");
amdgpu/vcn_v4_0_3.c: DRM_DEV_INFO(adev->dev, "VCN decode initialized
successfully(under %s).\n",
amdgpu/vcn_v4_0_3.c: DRM_DEV_INFO(adev->dev, "VCN decode is enabled
in VM mode\n");
amdgpu/jpeg_v4_0_5.c: DRM_DEV_INFO(adev->dev, "JPEG decode
initialized successfully under DPG Mode");
amdgpu/jpeg_v4_0_5.c: DRM_DEV_INFO(adev->dev, "JPEG%d decode is
enabled in VM mode\n", i);
amdgpu/jpeg_v5_0_0.c: DRM_DEV_INFO(adev->dev, "JPEG decode
initialized successfully under DPG Mode");
amdgpu/jpeg_v5_0_0.c: DRM_DEV_INFO(adev->dev, "JPEG%d decode is
enabled in VM mode\n", i);
amdgpu/jpeg_v4_0.c: DRM_DEV_INFO(adev->dev, "JPEG decode initialized
successfully.\n");
amdgpu/jpeg_v4_0.c: DRM_DEV_INFO(adev->dev, "JPEG decode is enabled
in VM mode\n");
If the rest of code in amdgpu uses DRM_INFO why should we make VCN and
JPEG special?
To address the identification of which GPUs - we need to check the
kernel message after each IP DISCOVERY.
I do not see a reason to mess them up.
Regards,
David
On 2024-05-09 16:59, Alex Deucher wrote:
On Thu, May 9, 2024 at 4:57 PM David (Ming Qiang) Wu<david....@amd.com> wrote:
amdgpu jpeg kernel message is different than others such as vcn:
[drm:jpeg_v5_0_0_hw_init [amdgpu]] JPEG decode initialized successfully.
This patch is to make them consistent.
The message after the change is:
[drm] JPEG decode initialized successfully.
Please convert the others to DRM_DEV_INFO instead. Otherwise we can't
tell which GPUs these messages refer to on multi-GPU systems.
Alex
Signed-off-by: David (Ming Qiang) Wu<david....@amd.com>
---
drivers/gpu/drm/amd/amdgpu/jpeg_v5_0_0.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/amd/amdgpu/jpeg_v5_0_0.c
b/drivers/gpu/drm/amd/amdgpu/jpeg_v5_0_0.c
index 64c856bfe0cb..4be0668ab97d 100644
--- a/drivers/gpu/drm/amd/amdgpu/jpeg_v5_0_0.c
+++ b/drivers/gpu/drm/amd/amdgpu/jpeg_v5_0_0.c
@@ -145,7 +145,7 @@ static int jpeg_v5_0_0_hw_init(void *handle)
if (r)
return r;
- DRM_DEV_INFO(adev->dev, "JPEG decode initialized successfully.\n");
+ DRM_INFO("JPEG decode initialized successfully.\n");
return 0;
}
@@ -549,7 +549,7 @@ static const struct amdgpu_ring_funcs
jpeg_v5_0_0_dec_ring_vm_funcs = {
static void jpeg_v5_0_0_set_dec_ring_funcs(struct amdgpu_device *adev)
{
adev->jpeg.inst->ring_dec->funcs = &jpeg_v5_0_0_dec_ring_vm_funcs;
- DRM_DEV_INFO(adev->dev, "JPEG decode is enabled in VM mode\n");
+ DRM_INFO("JPEG decode is enabled in VM mode\n");
}
static const struct amdgpu_irq_src_funcs jpeg_v5_0_0_irq_funcs = {
--
2.34.1
