Related question:
Once I have copied my data from PING into dma_area, and called
snd_pcm_period_elapsed, can I assume arecord has consumed that data by the
time i finish writing PONG, calling snd_pcm_period_elapsed, and hit the IRQ
to recopy PING?
in other words, what/where is the guarantee that arecord has consumed the
data in dma_area, such that the user can rewrite to it?
On Mon, Jul 11, 2016 at 12:33 PM, Rob Nertney <r...@rob-otics.com> wrote:
> Thanks Lars.
>
> My problem with the DMA is that it doesn't support cyclic mode, but does
> support SG mode. I have to create a new descriptor every time, and
> requeue/resubmit it. I don't want to drop any frames, so PONG is being
> received while PING is being copied and resubmitted to the Linux queue.
>
> On Mon, Jul 11, 2016 at 12:29 PM, Lars-Peter Clausen <l...@metafoo.de>
> wrote:
>
>> On 07/11/2016 09:10 PM, Rob Nertney wrote:
>> > Hi all,
>> >
>> > Could I please get a sanity check on my hw_params?
>> >
>> > I have a DMA which is providing between 1-16 channels of 4 bytes/ch
>> worth
>> > of data as a frame. I get an interrupt to my driver every frame's worth
>> of
>> > data (64 Bytes). The data is S32_LE, 16000Hz.
>> >
>> > My DMA has 2 buffers, PING and PONG. Each receives an IRQ on a frame
>> > length, and these local buffers are the size of a frame length
>> (64Bytes).
>> >
>> > #define MAX_BUFFER (64 * 2)
>> > static struct snd_pcm_hardware my_pcm_hw =
>> > {
>> > .info = (SNDRV_PCM_INFO_MMAP |
>> > SNDRV_PCM_INFO_INTERLEAVED |
>> > SNDRV_PCM_INFO_BLOCK_TRANSFER |
>> > SNDRV_PCM_INFO_MMAP_VALID),
>> > .formats = SNDRV_PCM_FMTBIT_S32,
>> > .rates = SNDRV_PCM_RATE_16000,
>> > .rate_min = 16000,
>> > .rate_max = 16000,
>> > .channels_min = 1,
>> > .channels_max = NUM_CHANNELS,
>> > .buffer_bytes_max = MAX_BUFFER,
>> > .period_bytes_min = 4,
>> > .period_bytes_max = 64,
>> > .periods_min = 2,
>> > .periods_max = 2,
>> > };
>> >
>> >
>> > My understanding is that the MAX_BUFFER needs to be at least twice the
>> size
>> > of a period so I don't underrun. .periods_max means the maximum number
>> of
>> > periods in a the alsa dma_area buffer, right?
>> >
>> > So when my DMA fires its ISR, I copy from its local PING buffer to the
>> > dma_area at offset 0, increment the buf_pos by the frame_length
>> (64Bytes),
>> > and call snd_pcm_period_elapsed.
>> >
>> > My DMA fires its ISR for its local PONG buffer, copies to the
>> > dma_area+buf_pos, increments buf_pos (now back to 0, since buffer only
>> > holds 2 frames/periods), and I call snd_pcm_period_elapsed again,
>> correct?
>>
>> Hi,
>>
>> In principle sounds OK. But there is not much of a point to use a
>> ping-pong buffer if you give the real buffer the same restrictions. You
>> might as well use the dma_area buffer as the target of the DMA in that
>> case. But since in your case the DMA is very restrictive in what it can
>> support it makes more sense to use the ping-pong buffer and broaden the
>> restrictions on the real buffer. Allow larger period sizes (only call
>> snd_pcm_period_elapsed() every N interrupts), allow more than two
>> periods and so on.
>>
>> - Lars
>>
>>
>
------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are
consuming the most bandwidth. Provides multi-vendor support for NetFlow,
J-Flow, sFlow and other flows. Make informed decisions using capacity planning
reports.http://sdm.link/zohodev2dev
_______________________________________________
Alsa-user mailing list
Alsa-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/alsa-user
