When I plug in a Tascam US-122 into my USB port, hotplug recognizes the
device as 1604:8006, as documented, and runs fxload to disconnect the
device, as documented.
The Tascam reloads as 1604:8007, as documented. If not already loaded,
snd_usb_usx2y loads, also as documented. Nothing else happens. The USB
LED on the US-122 does not light. No useful information is returned from
dmesg.
It appears to get hung up on the "hardware dependent device" /dev/hwC1D0
as shown later in this email.
I try to force the firmware load. As root, I attempt the command
"usx2yloader" and get the following:
usx2yloader: no US-X2Y-compatible cards found
Also as root, I attempt the command "usx2yloader -D hw:1,0" and get the
following:
usx2yloader: cannot open hwdep hw:1,0
Also as root, I attempt the command "usx2yloader -c 1" and get the
following:
usx2yloader: cannot open hwdep hw:1,0
As set in this example as USB device 001:010, also as root, I attempt
the command "usbx2yloader -u /proc/bus/usb/001/010" and get the following:
usx2yloader: no US-X2Y-compatible cards found
I have the following relevant software versions:
Kernel: 2.6.20.11
hotplug: 2004_03_29
fxload: 2002_04_11
alsa-drivers : 1.0.14 (built on top of kernel modules)
alsa-lib: 1.0.14a
alsa-utils: 1.0.14
alsa-tools (usx2yloader): 1.0.14
alsa-firmware (usx2yloader): 1.0.14
alsa-plugins: 1.0.14
Contents of /proc/bus/usb/devices:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.20.11 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:02.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.20.11 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:02.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 10 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1604 ProdID=8007 Rev= 0.01
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 5 Cls=ff(vend.) Sub=00 Prot=00 Driver=snd-usb-usx2y
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 21 Ivl=10ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 0 Alt= 1 #EPs= 7 Cls=ff(vend.) Sub=00 Prot=00 Driver=snd-usb-usx2y
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 21 Ivl=10ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=88(I) Atr=01(Isoc) MxPS= 200 Ivl=1ms
E: Ad=0a(O) Atr=01(Isoc) MxPS= 200 Ivl=1ms
I: If#= 0 Alt= 2 #EPs= 7 Cls=ff(vend.) Sub=00 Prot=00 Driver=snd-usb-usx2y
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 21 Ivl=10ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=88(I) Atr=01(Isoc) MxPS= 300 Ivl=1ms
E: Ad=0a(O) Atr=01(Isoc) MxPS= 300 Ivl=1ms
Contents of /proc/asound/cards:
0 [CK804 ]: NFORCE - NVidia CK804
NVidia CK804 with ALC850 at irq 18
1 [USX2Y ]: USB US-X2Y - TASCAM US-X2Y
TASCAM US-X2Y (1604:8007 if 0 at 001/010)
Contents of /proc/asound/devices:
0: [ 0] : control
16: [ 0- 0]: digital audio playback
18: [ 0- 2]: digital audio playback
24: [ 0- 0]: digital audio capture
25: [ 0- 1]: digital audio capture
32: [ 1] : control
33: : timer
36: [ 1- 0]: hardware dependent
Results of "ls -l /dev | grep '116,'":
crw-rw---- 1 root root 116, 0 Jul 11 20:19 controlC0
crw-rw---- 1 root root 116, 32 Jul 11 20:22 controlC1
crw-rw---- 1 root root 116, 36 Jul 11 20:22 hwC1D0
crw-rw---- 1 root root 116, 24 Jul 11 20:19 pcmC0D0c
crw-rw---- 1 root root 116, 16 Jul 11 20:19 pcmC0D0p
crw-rw---- 1 root root 116, 25 Jul 11 20:19 pcmC0D1c
crw-rw---- 1 root root 116, 18 Jul 11 20:19 pcmC0D2p
crw-rw---- 1 root root 116, 33 Jul 11 20:19 timer
Contents of /etc/asound.conf:
pcm.nforce-hw {
type hw
card 0
}
pcm.!default {
type plug
slave.pcm "nforce"
}
pcm.nforce {
type dmix
ipc_key 1234
slave {
pcm "hw:0,0"
period_time 0
period_size 1024
buffer_size 4096
rate 44100
}
}
ctl.nforce-hw {
type hw
card 0
}
pcm.usb-usx2y {
type hw
card 1
}
ctl.usb-usx2y {
type hw
card 1
}
Contents of relevant portion of /etc/modprobe.conf:
alias char-major-116 snd
alias sound-service-0-0 snd_mixer_oss
alias sound-service-0-1 snd_seq_oss
alias sound-service-0-3 snd_pcm_oss
alias sound-service-0-8 snd_seq_oss
alias sound-service-0-12 snd_pcm_oss
alias snd-card-0 snd_intel8x0
alias snd-card-1 snd_usb_usx2y
I feel like I'm missing a step somewhere, and I don't know what it is.
No documentation seems to help out here in my singular case. Anyone else
out there who can observe their example tell me what's up?
--
Curtis R. Anderson, Co-creator of "Gleepy the Hen", still
"In Heaven there is no beer / That's why we drink it here ..."
http://www.gleepy.net/ mailto:[EMAIL PROTECTED]
mailto:[EMAIL PROTECTED] (and others) Yahoo!: gleepythehen
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
Alsa-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-user