You guys are awesome.

On 7/15/2020 9:40 AM, ch...@wbmfg.com wrote:
At my age, there is no difference.
*From:* Ken Hohhof
*Sent:* Wednesday, July 15, 2020 7:13 AM
*To:* 'AnimalFarm Microwave Users Group'
*Subject:* Re: [AFMUG] Ot: I want my money back

Maybe use the concrete silos.  I’ve seen Rohn towers attached to the sides extending above the top, but these don’t have steel hoops.

And I had to read your post a couple times to realize you were talking about an old (man lift), not an (old man) lift.

*From:* AF <af-boun...@af.afmug.com> *On Behalf Of *Chuck McCown
*Sent:* Wednesday, July 15, 2020 7:49 AM
*To:* AnimalFarm Microwave Users Group <af@af.afmug.com>
*Subject:* Re: [AFMUG] Ot: I want my money back

When I had a tower failure I took an old man lift, put antennas on it and got service restored.

Sent from my iPhone



    On Jul 14, 2020, at 9:20 PM, Steve Jones
    <thatoneguyst...@gmail.com> wrote:

    

    I blame chuck's mounts. Has nothing to do with them cutting 1 inch
    guy wires, all chucks fault.

    I actually did see an mtow in the middle of the pile that looks
    good I hope to recover out of spite

    Not going to lie, if I had tear ducts, I would maybe have had some
    gay water coming from my eyes this weekend. Almost 15 years of
    finding solutions, and getting there, wiped out by some wind. I'll
    find a solution, it's what idiots like us do, but all that work
    wiped off the map kind of sucks.. wife was pissed and made me come
    home cause of some shit 2 years ago on this day where were went to
    a church and have each other some shiny rocks that some prick
    hammered into a circle. I didnt even have time to get her some
    flowers to die

    On Tue, Jul 14, 2020, 7:59 PM James Howard <ja...@litewire.net> wrote:

        Should have named that site “Little Moe with the Gimpy Leg”……

        *From:* AF [mailto:af-boun...@af.afmug.com] *On Behalf Of *Ken
        Hohhof
        *Sent:* Tuesday, July 14, 2020 7:55 PM
        *To:* 'AnimalFarm Microwave Users Group' <af@af.afmug.com>
        *Subject:* Re: [AFMUG] Ot: I want my money back

        That doesn’t look like an intentional demolition.  Did it just
        fall over?  Looks like it was kind of a POS leg.  I hope
        nobody was on it at the time.

        *From:* AF <af-boun...@af.afmug.com> *On Behalf Of *Steve Jones
        *Sent:* Tuesday, July 14, 2020 7:25 PM
        *To:* AnimalFarm Microwave Users Group <af@af.afmug.com>
        *Subject:* Re: [AFMUG] Ot: I want my money back

        I'm just saying the leg wasn't on the ground when I put the
        mounts on, now the leg is on the ground.

        On Tue, Jul 14, 2020, 5:03 PM Bill Prince
        <part15...@gmail.com> wrote:

            Those are too close to even figure out where you are. You
            need to backup 50 or 100 feet and get a context picture.

            bp

            <part15sbs{at}gmail{dot}com>

            On 7/14/2020 2:38 PM, Steve Jones wrote:

                Faulty faulty faulty

-- AF mailing list
            AF@af.afmug.com
            http://af.afmug.com/mailman/listinfo/af_af.afmug.com

        ------------------------------------------------------------------------

        *Total Control Panel*

                

        Login <https://asp.reflexion.net/login?domain=litewire.net>

        To: ja...@litewire.net
        
<https://asp.reflexion.net/address-properties?aID=242260993&domain=litewire.net>

        From: af-boun...@af.afmug.com

                

        /You received this message because the domain afmug.com
        <http://afmug.com> is on your allow list./

-- AF mailing list
        AF@af.afmug.com
        http://af.afmug.com/mailman/listinfo/af_af.afmug.com

-- AF mailing list
    AF@af.afmug.com
    http://af.afmug.com/mailman/listinfo/af_af.afmug.com

------------------------------------------------------------------------
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com

-- 
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com

Reply via email to