Jim, It looks indeed to be a HW problem with the library (which is brand new, so that cancels option 1 and 2). I was just surprised that the tapes could be labelled as data is wrtten to them then too. But apperantly the HW issues only pop-up when you start sending the backup data, which are larger then a label of course. thanks, Kurt
________________________________ Van: ADSM: Dist Stor Manager namens JN Verzonden: di 3/14/2006 18:53 Aan: ADSM-L@VM.MARIST.EDU Onderwerp: Re: [ADSM-L] MSL6030 TSM write failure Hi Kurt, In my experience, the errors that you are seeing are primarily caused by one of three problems: 1) The tape drive is dirty and needs to be cleaned 2) The tape cartridge is bad and needs to be destroyed 3) The Tape drive has a physical problem that needs to be fixed via replacement or maintenance. I hope one of these solutions works for you. Jim -----Original Message----- From: ADSM: Dist Stor Manager [mailto:[EMAIL PROTECTED] On Behalf Of Kurt Beyers Sent: Tuesday, March 14, 2006 1:01 AM To: ADSM-L@VM.MARIST.EDU Subject: [ADSM-L] MSL6030 TSM write failure Hello, A quick (?) question. My setup is the following: TSM 5.3.2 server with a MSL6030 SCSI attached library (2 HP-Ultrium 3 drives). The library has been defined in TSM and the labelling of the tapes went fine. However a migrate of the diskpool towards the LTOPool fails with the following messages: ANR0984I Process 42 for MIGRATION started in the BACKGROUND at 08:45:30. ANR2110I MIGRATE STGPOOL started as process 42. ANR1000I Migration process 42 started for storage pool DISKPOOL manually, highMig=90, lowMig=0, duration=No. ANR8337I LTO volume HK3722L3 mounted in drive DRIVE1 (mt1.0.0.5). ANR1340I Scratch volume HK3722L3 is now defined in storage pool LTOPOOL. ANR0513I Process 42 opened output volume HK3722L3. ANR8302E I/O error on drive DRIVE1 (mt1.0.0.5) with volume HK3722L3 (OP=WRITE, Error Number=1117, CC=208, KEY=0B, ASC=47, ASCQ=03, SENSE=70.00.0B.00.00.00.00.10.00.00.00.00.47.03.00.00.00.00.00.00.00.00., Description=Command aborted). Refer to Appendix D in the 'Messages' manual for recommended action. ANR1411W Access mode for volume HK3722L3 now set to "read-only" due to write error. ANR0515I Process 42 closed volume HK3722L3. What am I missing here? The library configuration in TSM is as follows: -The TSM device driver is used and the library is detected by the tsmdlst.exe program as follows: Tivoli Storage Manager -- Device List Utility Licensed Materials - Property of IBM 5697-TSM (C) Copyright IBM Corporation 2000, 2005. All rights reserved. U.S. Government Users Restricted Rights - Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corporation. Computer Name: TSM-server OS Version: 5.2 OS Build #: 3790 TSM Device Driver: TSMScsi - Running 2 HBAs were detected. Manufacturer Model Driver Version Firmware Description ---------------------------------------------------------------------------- ------------------------------------ QLogic Corporation QLA2340 ql2300.sys 9.0.2.11 (w32 IP) 3.03.12 QLogic QLA2340 Fibre Channel Adapter QLogic Corporation QLA2340 ql2300.sys 9.0.2.11 (w32 IP) 0.00.00 QLogic QLA2340 Fibre Channel Adapter TSM Name ID LUN Bus Port SSN WWN TSM Type Device Identifier ---------------------------------------------------------------------------- ------------------------------------ lb0.0.0.5 0 0 0 5 - - LIBRARY HP MSL6000 Series 0507 mt1.0.0.5 1 0 0 5 - - LTO HP Ultrium 3-SCSI G24W mt2.0.0.5 2 0 0 5 - - LTO HP Ultrium 3-SCSI G24W Completed in: 0 days, 0 hours, 0 minutes, 1 seconds. -The library is defined in TSM with: tsm: SRV-SPGR-BACKUP_SERVER1>q library f=d Library Name: MSL6030 Library Type: SCSI WWN: 00900D06254B8000 Serial Number: 2U2527002X AutoLabel: No Reset Drives: No Last Update by (administrator): ADMIN tsm: SRV-SPGR-BACKUP_SERVER1>q drive f=d Library Name: MSL6030 Drive Name: DRIVE1 Device Type: LTO On-Line: Yes Read Formats: ULTRIUM3C,ULTRIUM3,ULTRIUM2C,ULTRIUM2,ULTRIUMC,ULTRIUM Write Formats: ULTRIUM3C,ULTRIUM3,ULTRIUM2C,ULTRIUM2 Element: 480 Drive State: EMPTY Volume Name: Allocated to: WWN: 50060B000034589E Serial Number: HU105252G0 Library Name: MSL6030 Drive Name: DRIVE2 Device Type: LTO On-Line: Yes Read Formats: ULTRIUM3C,ULTRIUM3,ULTRIUM2C,ULTRIUM2,ULTRIUMC,ULTRIUM Write Formats: ULTRIUM3C,ULTRIUM3,ULTRIUM2C,ULTRIUM2 Element: 481 Drive State: EMPTY Volume Name: Allocated to: WWN: 50060B000034586E Serial Number: HU105252FH tsm: SRV-SPGR-BACKUP_SERVER1>q path f=d Source Name: SRV-SPGR-BACKUP_SERVER1 Source Type: SERVER Destination Name: MSL6030 Destination Type: LIBRARY Library: Node Name: Device: LB0.0.0.5 Source Name: SRV-SPGR-BACKUP_SERVER1 Source Type: SERVER Destination Name: DRIVE1 Destination Type: DRIVE Library: MSL6030 Node Name: Device: mt1.0.0.5 Source Name: SRV-SPGR-BACKUP_SERVER1 Source Type: SERVER Destination Name: DRIVE2 Destination Type: DRIVE Library: MSL6030 Node Name: Device: mt2.0.0.5 thanks, Kurt
