Roland, Thank you, that’s very helpful Any other opinions? I’m very happy to delete with consensus and appreciate the reviews on this particular issue as well as on the draft.
Best regards, Kathleen From: Roland Shoemaker <[email protected]> Sent: Tuesday, July 28, 2020 3:27 PM To: Kathleen Moriarty Cc: Carl Mehner; Moriarty, Kathleen; IETF ACME Subject: Re: [Acme] CAA in draft-ietf-acme-client-01.txt [EXTERNAL EMAIL] I think the disconnect here is between CAs and Relying Applications (i.e. browsers) using CAA. The CA should use CAA to validate if they have authority to issue, but the relying application must not because the CAA records are only applicable at the time of issuance and there is no guarantee that the current CAA records may match the records that were present in the past (i.e. I may set my CAA record to allow "example-ca", issue a certificate, and then set my CAA record to an empty string to prevent issuance from anyone, the check is valid at the time of issuance, but anyone trying to do post-issuance validation would fail since the record has changed). I would support removing the paragraph. On Tue, Jul 28, 2020 at 7:57 AM Kathleen Moriarty <[email protected]<mailto:[email protected]>> wrote: Hello Carl, Thank you for your review and I apologize for my extremely tardy response. On Mon, May 18, 2020 at 11:41 AM Carl Mehner <[email protected]<mailto:[email protected]>> wrote: Looking at the latest draft for acme-client, I noticed that it mentions CAA: CAA helps as anyone verifying a certificate used for code signing can verify that the CA used has been authorized to issue certificates for that organization. However, in the CAA RFC it states: Relying Applications MUST NOT use CAA records as part of certificate validation. I propose removing the statement in acme-client about CAA that is quoted above. I recall having gone through this conversation before to wind up where the draft is now. RFC8555 has the following: caaIdentities (optional, array of string): The hostnames that the ACME server recognizes as referring to itself for the purposes of CAA record validation as defined in [RFC6844<https://tools.ietf.org/html/rfc6844>]. Each string MUST represent the same sequence of ASCII code points that the server will expect to see as the "Issuer Domain Name" in a CAA issue or issuewild property tag. This allows clients to determine the correct issuer domain name to use when configuring CAA records. Section 9.7.8 has the following: Validation methods do not have to be compatible with ACME in order to be registered. For example, a CA might wish to register a validation method to support its use with the ACME extensions to CAA [ACME-CAA<https://tools.ietf.org/html/rfc8555#ref-ACME-CAA>]. Section 11.2 has the following: An ACME-based CA must only use a resolver if it trusts the resolver and every component of the network route by which it is accessed. Therefore, it is RECOMMENDED that ACME-based CAs operate their own DNSSEC-validating resolvers within their trusted network and use these resolvers both for CAA record lookups and all record lookups in furtherance of a challenge scheme (A, AAAA, TXT, etc.). As you point out, https://tools.ietf.org/html/rfc6844, advises against its use. I am happy to edit to consensus. If a change is needed, I can turn that around quickly. Best regards, Kathleen -carl mehner _______________________________________________ Acme mailing list [email protected]<mailto:[email protected]> https://www.ietf.org/mailman/listinfo/acme -- Best regards, Kathleen _______________________________________________ Acme mailing list [email protected]<mailto:[email protected]> https://www.ietf.org/mailman/listinfo/acme
_______________________________________________ Acme mailing list [email protected] https://www.ietf.org/mailman/listinfo/acme
